Epoxy Tabletop Resin - Epoxy Bar Top Resin
Water Clear Epoxy Casting Resin
Product #214
Table Top Resin Description
Product #214 Water Clear Epoxy Casting - Tabletop Resin - Bar Top Resin is an all-purpose, low viscosity epoxy resin system for coating wood and concrete counter tops, tabletops, bar tops and similar applications.
Product #214 Water Clear Casting-Tabletop-Epoxy Bar Top Resin is commonly used as a clear self-leveling flooring material, where an extremely flat and level floor is required over concrete and wood. Product #214 Casting-Epoxy Tabletop-Epoxy Bar Top Resin is used extensively for ultra flat leveling of surfaces under equipment, where a very strong ultra flat bearing surface is a must. It is also used successfully for ultra flat floors for stages, dance floor, and clean rooms.
Product #214 Clear Casting-Tabletop-Bar Top Resin is used as a clear adhesive matrix for specialty colored glass and colored aggregate flooring and tiles. Product #214 Clear Casting-Clear Tabletop Resin - Clear Bar Top Resin forms a glossy, hard surface, which is resistant to stains. It is also used extensively as a water clear casting resin.
Product #214 Clear Casting- Clear Tabletop- Clear Bar Top Resin has excellent clarity and color retention. Product #214 Clear Casting Resin-Tabletop Resin-Bar Top Resin has zero (0) VOC making it essentially odorless and can therefore be used in occupied areas.
Advantages of Clear Table Top Resin #214
- Low odor for use in occupied areas
- Low viscosity - good wetting properties
- Meets USDA standards for use in food handling applications
- Glossy finish
- Stain resistant
- Zero (0) VOC - No VOC means it meets the toughest low VOC standards.
Consideration When Using Clear Table Top Resin
- Minimum application temperature of Product #214 Clear Epoxy Casting-Tabletop-Bar Top Resin is 50° F.
- Substrate to receive Product #214 Water Clear Resin must be free of curing agents and any foreign materials.
Surface Preparation of Table Top Epoxy
Surface Preparation is the most critical portion to any successful epoxy application. All substrates to receive Product #214 Water Clear Casting-Tabletop-Bar Top Resin must be properly cleaned and prepared. Substrate must be free of oil, paint, sealer, caulking, and all other contamination that will interfere with the bonding of this material. Please see Surface Preparation. Contact us for more details.
Mixing Instructions for Clear Resin #214
Stir each component separately. Combine 2 parts A to one part B by volume into a clean container. Stir for three minutes, with an Mixing Paddle, scrapping bottom and sides of container frequently. Do not add thinners.
APPLICATION PROPERTIES @77°F |
||
| Mix Ratio | 2:1 By Volume | |
| Viscosity (mixed) | 950 CPS | |
| Pot Life (200 gr.) | 30-40 minutes @ 70° F. | |
| VOC | 0 | |
| Cure Time (recoat) | 10-14 Hours | |
| Ultimate cure @ 74 Degrees F. | 5 days | |
| Color | Clear | |
| Packaging Unit Size | 3 gallon units | |
Performance Properties |
||
| Tensile Strength ASTM D-638 | 8500 psi | |
| Elongation ASTM D-638 | 5.5% | |
| Adhesion to metal | 2500 psi | |
| Adhesion to concrete ACI Committee 403 | 350 psi (Concrete fails) | |
| Hardness ASTM D-2240 | 80 (Shore D) | |
| Abrasion Resistance ASTM C-501 | 35-40 mg loss (CS-17 wheel, 1kg load, 1000 Cycles) | |
| Service Temperature MIL-D-3134F | 160 F
(Immersion) 185 F (Dry Heat) |
|
| Impact Resistance MTI-D-3134F§ 4.7.3 | Withstands
16ft/lbs no cracking, delamination or Chipping. |
|
| Indention MIL-D-3134F §4.7.4 | Withstands 2000
lbs./sq. in. for 30 minutes without indentation |
|
| Elevated Temperature
Resistance MIL-D-3134F § 4.7.5 |
No slip or flow
at required temperatures at 158 F. |
|
| Water Absorption ASTM
D-670-63 (24 hour immersion) |
0.10% maximum | |
| Flexural Strength ASTM D-790 | 8000 psi | |
| Compressive Strength ASTM D-695 | 11000 psi | |
Application of Table Top / Bar Top Epoxy
Application of Product #214 Water Clear Resin will vary with application method. Be careful not to incorporate bubbles into the coating. Typical pours are in the 1/16 inch to 1/2 inch thick range per coat. If a second coat is desired, remove all dust, if more than 24 hours after the last coat lightly sand, and then apply second coat.
Safety Precautions When Using Epoxy
Keep away from children. Refer to the Material Safety Data Sheets (MSDS forms) pertaining to this product before using. Avoid contact with skin or eyes. Prolonged or repeated exposure may cause eye and skin irritation. If skin contact occurs, wash immediately with soap and water. If contact with eyes occurs, flush eyes as required with clean water and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.
Cleaning up Epoxy Tabletop - Bar Top Resin
Remove Product #214 Water Clear Resin from all tools and equipment before the system gels. Use MEK, Acetone, or any lacquer solvent.
Chemical Resistance of #214 Bar Top Resin | |||
| Acetic Acid 5% | L | Lactic Acid- 15% | R |
| Acetone | L | Methyl Ethyl Ketone | L |
| Methyl Ethyl Ketone | L | Nitric Acid 10% | R |
| Bleach | L | Sodium Hydroxide 50% | R |
| Citric Acid 30% | R | Skydrol | R |
| Crude Oil & Diesel Fuel | R | Sulfuric Acid 20% | R |
| Ethylene Glycol | R | Toluene | R |
| Fatty Acids | L | Urea | R |
| Gasoline | R | Vinegar | L |
| Hydrochloric Acid 15% | R | Xylene | R |
R=Recommended for continuous service L=Limited recommendation, occasional spills.
Coverage: 231 cubic inches per gallon. At 1/8 inch thick 12.8 SF Per gallon. Use the calculator below to double check your estimate.