Epoxy.com Product #22Pourable and Pumpable Epoxy MortarDESCRIPTION:Epoxy.com Product #22 Pourable and Pumpable Epoxy Mortar is a moisture insensitive, two-component, 100% solids epoxy resin. This material is specifically designed for use with the Epoxy.com Fiberglass Systems & Shapes. Product #22 Pourable and Pumpable Mortar can also be used as self-leveling flooring. It has a long potlife for easy pumping and exhibits exceptional flow. ADVANTAGES:
PHYSICAL PROPERTIES:
SURFACE PREPARATIONFor best results, areas to receive the Epoxy.com Product #22 Pourable and Pumpable Epoxy Grout should be free of laitance. Grease, oil or other contaminants that would inhibit bond. See www.epoxy.com/surfaceprep.aspx for detailed surface preparation recommendations MIXING:Combine (2) two gallons A Component with one (1) gallon B Component, mix with a low speed drill andEpoxy.com -Mixing Paddle for two minutes. Add (3) 50 lb. bags of the C Component. Mix until uniform. Scrape sides and bottom to ensure thorough mixing. Pump or pour immediately after mixing. If greater flow is required, use less filler. APPLICATION:Apply when ambient temperatures are 40F and above. Pump or pour Epoxy.com Product #22 Pourable and Pumpable Epoxy Grout into wet or dry annular void between a jacket or form and the existing structure. is easily pumped with a progressive cavity pump. For higher flow, the amount of C component can be decreased to two (2) bags for 3 gallons of mixed epoxy. COVERAGE:3 gallons of mixed Epoxy.com Product #22 Pourable and Pumpable Epoxy Grout with (3) 50 pound bags of C component will yield approximately +/- 2,400 cubic inches (39.3 liters) of grout. Using less C component will increase the flow and lower the yield. SHELF LIFE:1 year minimum PACKAGINGEpoxy.com Product #22 Pourable and Pumpable Epoxy Grout is available in 3 gallon units (2 gallons A Component, 1 gallon B Component plus (3) 50 lb. bags C Component) or a 15 gallon unit (10 gallons A Component, 5 gallons B Component plus (15) 50 lb. bags C Component). LIMITATIONSEpoxy.com Product #22 Pourable and Pumpable Epoxy Grout should not be used when ambient or surface temperature is below 40° F (4° C). Lower temperatures slow the set time and reduce its ability to flow. Friction from pumping can accelerate setting time. CAUTION"A" Component contains epoxy resin. DANGER! "B" Component contains alkaline amines; strong sensitizer. "C" Component contains silicon dioxide. Avoid breathing dust. Liquids may cause skin sensitization or other allergic responses. Use with good ventilation, particularly if material is heated or sprayed. Prevent all contact with skin or eyes. Wear protective clothing, goggles, gloves and/or barrier creams. Keep container closed when not in use. Wash thoroughly after handling. FIRST AIDIn case of skin contact, immediately wash with soap and water. In case of eye contact, flush eyes with copious amounts of water for at least fifteen (15) minutes. Remove contaminated clothing and shoes. If irritation persists, seek medical attention. Wash clothing before reuse. FOR INDUSTRIAL USE ONLY. KEEP AWAY FROM CHILDREN. |
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments Website: www.epoxy.com 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2010 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products]
[Where to Start] [[Bonding Systems]
[Chip Floors] [Chemical Resistance]
|
