Epoxy.com Product #707Splash Zone and Underwater PasteDESCRIPTIONEpoxy.com Product #707 Splash Zone Coating and Underwater Paste is a moisture-insensitive, two-component, 100% solids epoxy-resin system. When mixed at a 1:1 ratio, by volume, this product produces a paste-like material that is ideal for protection or restoration of concrete, steel and timber piles and other structural elements in marine environments. ADVANTAGES
PHYSICAL PROPERTIES
MIXINGMix only as much as you can use within 2 hours or less at 70 degrees F. If the temperature is higher your working time will be much shorter. It is always better to start with smaller batches and to gradually increase the size, to be sure that you have enough working time. Material temperature should be a minimum of 60°F for ease of mixing. Mix "A" & "B" Components together, by hand, until a uniform gray color is achieved. SURFACE PREPARATIONRemove all deteriorated material, barnacles or other marine growth by mechanical abrasion, water or sand blasting. Typically the better the surface preparation, the better the bond. To avoid contamination, apply Epoxy.com Product #707 Splash Zone Coating and Underwater Paste to prepared surface as quickly as possible. It is always best to do a mockup to verify that your surface preparation is adequate. APPLICATIONFor best results, apply Epoxy.com Product #707 Splash Zone Coating and Underwater Paste by hand using tight-fitting rubber or plastic gloves. (Wet gloves with slightly soapy water before working with material.) Press material onto surface and knead into place in maximum lift thickness of approximately 2". Smooth gently by rubbing with gloves using water as a lubricant. For smaller areas you can use a concrete grout bag. LIMITATIONSDo not thin Epoxy.com Product #707 Splash Zone Coating and Underwater Paste. Since conditions content vary greatly, it is recommended that a sample application be made to ensure the intended performance. Do not apply when water or ambient temperature is below 50°F. COVERAGEOne (1) gallon of Epoxy.com Product #707 Splash Zone Coating and Underwater Paste will yield 231 CI and cover 12.8 SF @ 1/8" thickness 125 mil. PACKAGINGEpoxy.com Product #707 Splash Zone Coating and Underwater Paste is packaged in four (4) gallon and ten (10) gallon units. SHELF LIFETwo (2) years for Components "A" and "B". CAUTIONEpoxy.com Product #707 Splash Zone Coating and Underwater Paste Contains A Component contains epoxy resins. B Component contains organic amines which are strong sensitizers. WARNING! May cause skin sensitization, burns or other allergic responses. Avoid inhalation of vapor. Use good ventilation, particularly if material is heated. Prevent all contact with skin and eyes. Wear protective clothing, goggles and/or barrier creams. Wash thoroughly after handling. FIRST AID: In case of contact, immediately flush eyes or skin with plenty of water for at least fifteen (15) minutes. Remove contaminated clothing before re-use. Discard contaminated shoes. |
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments Website: www.epoxy.com 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2010 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products]
[Where to Start] [[Bonding Systems]
[Chip Floors] [Chemical Resistance]
|
