Epoxy.com Product #214
GENERAL DESCRIPTION
Epoxy.com Product #214 is an all-purpose, low viscosity Epoxy System for coating wood and concrete counter tops, tabletops, bar tops and similar applications. Product #214 is commonly used as a clear self-leveling flooring material, where an extremely flat and level floor is required over concrete and wood. Also used as a clear adhesive matrix for specialty colored glass and colored aggregate flooring and tiles. Product #214 forms a glossy, hard surface, which is resistant to stains. Product #214 has excellent clarity and color retention. It is essentially odorless and can therefore be used in occupied areas.
ADVANTAGES
| Low odor for use in occupied areas |
| Low viscosity - good wetting properties |
| Meets USDA standards for use in food handling applications |
| Glossy finish |
| Stain resistant |
CONSIDERATIONS
| Minimum application temperature of Normal Cure 50 Degrees F. |
| Substrate must be free of curing agents and any foreign materials. |
| Slight color variation can be expected from batch to batch. |
| Pigmented version should not be used as a coating. |
SURFACE PREPARATION
Surface Preparation is the most critical portion to any successful epoxy
application. All substrates must be properly cleaned and prepared. Substrate
must be free of oil, paint, sealer, caulking, and all other contamination that
will interfere with the bonding of this material. Please see
Surface Preparation. Contact Epoxy Systems, Inc.
for more details.
Stir each component separately. Combine 2 parts A to one part B by weight
into a clean container. Stir for three minutes, scrapping bottom and sides of
container frequently. Do not add thinners.
| APPLICATION PROPERTIES @77 DEGREES F | ||
| Mix Ratio | 2:1 By Volume | |
| Viscosity (mixed) | 950 CPS | |
| Pot Life (200 gr.) | 30-40 minutes @ 70 degrees F. | |
| VOC | 0 | |
| Cure Time (recoat) | 10-14 Hours | |
| Ultimate cure @ 74 Degrees F. | 5 days | |
| Color | Clear or pigmented | |
| Packaging Unit Size | 3 gallon units | |
| Performance Properties | ||
| Tensile Strength ASTM D-638 | 8500 p.s.i | |
| Elongation ASTM D-638 | 5.5% | |
| Adhesion to metal | 2500 p.s.i | |
| Adhesion to concrete ACI Committee 403 | 350 p.s.i (Concrete fails) | |
| Hardness ASTM D-2240 | 80 (Shore D) | |
| Abrasion Resistance ASTM C-501 | 35-40 mg loss (CS-17 wheel, 1kg load, 1000 Cycles) | |
| Service Temperature MIL-D-3134F | 160 F
(Immersion) 185 F (Dry Heat) |
|
| Impact Resistance MTI-D-3134F ss 4.7.3 | Withstands
16ft/lbs no cracking, delamination or Chipping. |
|
| Indention MIL-D-3134F ss 4.7.4 | Withstands 2000
lbs./sq. in. for 30 minutes without indentation |
|
| Elevated Temperature
Resistance MIL-D-3134F ss 4.7.5 |
No slip or flow
at required temperatures at 158 F. |
|
| Water Absorption ASTM
D-670-63 (24 hour immersion) |
0.10% maximum | |
| Flexural Strength ASTM D-790 | 8000 p.s.i | |
| Compressive Strength ASTM D-695 | 11000 p.s.i | |
APPLICATION
Will vary with application method. Be careful not to incorporate bubbles into the coating. If a second coat is desired, lightly sand the first coat, remove all dust, and then apply second coat.
SAFETY PRECAUTIONS
CLEANING
All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent.
| CHEMICAL RESISTANCE | |||
| Acetic Acid 5% | L | Lactic Acid- 15% | R |
| Acetone | L | Methyl Ethyl Ketone | L |
| Bleach | L | Nitric Acid 10% | R |
| Citric Acid 30% | R | Skydrol | R |
| Crude Oil | R | Sodium Hydroxide 50% | R |
| Diesel Fuel | R | Sulfuric Acid 20% | R |
| Ethylene Glycol | R | Toluene | R |
| Fatty Acids | L | Urea | R |
| Gasoline | R | Vinegar | L |
| Hydrochloric Acid 15% | R | Xylene | R |
R=Recommended for continuous service L=Limited recommendation, occasional spills.