Epoxy Coating General Purpose
Epoxy.com Product #1
100% Solids Hi-Build Epoxy Coating - Zero VOC
EPOXY COATING DESCRIPTION
Epoxy.com Product #1 All Purpose Epoxy Coating in a Burlington, Vermont Water Plant
Epoxy.com Product #1 a two component, zero (0) VOC, 100% solids epoxy Hi-Build epoxy coating used for high foot traffic and light to moderate forklift traffic areas where abrasion resistance is required; for protection against mild corrosion and as a decorative waterproof coating for walls, floors, tanks, etc. It can be broadcast with appropriate silica sand (contact Epoxy.com Technical Support for a recommendation), to create a thicker flooring system in high abrasion situations.
EPOXY COATING ADVANTAGES
- Moisture Insensitive
- Ceramic like finish
- Sprayable
- Solvent Free - 0.0 lbs VOC
- Waterproof
- Extremely Durable
- Chemical Resistant
SURFACE PREPARATION FOR EPOXY
Epoxy.com Product #1 All Purpose Epoxy Coating on Plywood walls and Floors. Installation and Picture by: Suwannee River Rendezvous Resort & Campground
Surface to receive Epoxy.com Product #1 All Purpose, 100% Solids, VOC free Epoxy Coating must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, or mechanical abrasion. Remove water and dust from all surfaces with an oil free blast immediately prior to application. See Epoxy.com Surface Preparation Guide form more details.
EPOXY MIXING INSTRUCTIONS
Temperature of Epoxy.com Product #1, VOC Free, All Purpose Epoxy Coating must be 50 °F or above at time of mixing. Stir each component separately before blending. Mix two parts by volume of Part A with one part by volume of Part B for three minutes with a low speed electric drill motor equipped with a mixing paddle.
EPOXY APPLICATION
Over Concrete surfaces Epoxy.com Product #899 Primer is recommended. Then apply Epoxy.com Product #1 All Purpose Epoxy Coating with a roller, brush, or spray equipment. Two coats are recommended. Thickness per coat should be 7-10 mils. Seven days cure time is required to reach maximum chemical resistance. For more information before installing please see installation tips at https://www.epoxy.com/install.htm.
EPOXY LIMITATIONS
DO NOT apply at temperatures below 40° F. Surface must be dry.
Epoxy.com Product #1 All Purpose Epoxy Coating on the floor of Tri-Town Water District (Vermont) Floor
EPOXY SAFETY PRECAUTION
Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.
EPOXY CLEANING
All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent
EPOXY APPLICATION PROPERTIES @77° F |
|
| Mix Ratio | 2:1 By Volume |
| Viscosity (mixed) | 950 CPS |
| Pot Life (200 gr.) in minutes @70° F. | 30-40 (normal cure) |
| VOC Content | "0.0" (zero) |
| Set Time in Hours @ 70°F. | 10-12 (normal cure) |
| Initial Cure | 24 Hours |
| Final Cure | 5 Days |
| Packaging Unit Size | 3 gal. 15 gal. |
| Standard Colors | See Color Chart |
| Typical Coefficient of Friction-Rubber Shoe Surface with Epoxy.com Product # 50 Anti-skid Fine Non-Skid Added | ASTM F-489 |
| Static Friction w/ Saltwater Solutions on surface | 0.90-0.97 |
| Static Friction w/ oil on Surface | 0.72-0.75 |
| Sliding Friction w/ Saltwater Solution on Surface | 0.87-.090 |
Click the picture
of color card below for a larger version of this picture of the
color chart.
Please note:
The picture to the right is a photographic reproduction
of the color card for this product. The photo reproduction process and
your monitor and/or printer will change these colors. This chart is to
give you an idea of the colors available and not intended for critical
color selections.
Epoxy.com Coating Installation Guide
Epoxy.com Chemical Resistance Chart for Epoxy.com Produc #1 All Purpose Epoxy Coating, set side by side with other commonly used Epoxy.com Coating Systems.
Other customers who visited this page also visited:
- Epoxy.com Product #1W - Wall Grade Version of Epoxy.com Product #1
- Epoxy.com Product #2 - Chemical Resistant Epoxy coating.
- Epoxy.com Product #315BC - Chip Flooring System Base coat.
- Epoxy.com Product #315NH - A standard chemical resistance coating, that can be shipped by air, and easily shipped to destinations outside the US.
- Epoxy.com Product #633 - Epoxy Novolac Coating - extremely chemical resistant
- Epoxy.com Product #641 - High Temperature Epoxy Coating.
- Epoxy.com Chip Flooring System
- Epoxy.com Coatings Page.
Download a spreadsheet in Microsoft Excel Format worksheets/CoatingsCalculator.xls