Epoxy.com Product #461
Heavy Duty Duel Component Chemical and Abrasion Resistant Aliphatic Urethane
Ultra High Solids Aliphatic Urethane for the Most Demanding Jobs
Epoxy.com Product #461 Ultra High Solids Aliphatic Urethane is a two component, chemical resistant, ultra high solids aliphatic polyurethane coating
designed to be used where there is high traffic and high abrasion resistance
Epoxy.com Product #461 is a low VOC, compliant urethane that meets all federal and state environmental air quality standards. The high gloss or satin finish offers excellent abrasion resistance, chemical and stain resistance.
Epoxy.com Product #461 Ultra High Solids Aliphatic Urethane can be used equally well on vertical or horizontal surfaces. It is ideal for concrete floors and walls in warehouses, storage facilities, aircraft hangars, animal housing, restrooms, vehicle maintenance facilities, and numerous other applications. Available in clear and pigmented, Epoxy.com Product #461 can be used as a finish coating option for most
Epoxy.com FLOORING SYSTEMS. The Epoxy.com Product #461 is for use in high traffic/high wear applications.
- Excellent Abrasion Resistance
- Excellent Chemical and Stain Resistance
- Suitable for Both Exterior and Interior Applications
- May be Used for Both Horizontal and Vertical Applications
- Compliant to Low VOC Air Regulations, Low Odor
- Substrate moisture testing and preparation is required as outlined in the
Epoxy.com Surface Preparation Procedures
- Substrate must be free of dirt, waxes, curing agents, and other foreign materials
- Minimum/Maximum Application Temperature: 50°F/90°F
- Minimum/Maximum Relative Humidity: 30%/90%
Epoxy.com Product #461 Ultra High Solids Aliphatic Urethane is two, three or four component, catalyzed, chemical resistant, moisture cure aliphatic polyurethane.
Surface Preparation is the most critical portion of any successful resinous flooring system application. All substrates must be properly prepared as outlined in
Epoxy.com Surface Preparation Guide.
Epoxy.com Product #461 Ultra High Solids Aliphatic Urethane is normally applied with a brush, short nap roller, or squeegee and back-rolled very thoroughly with a short nap roller. Care should be taken to minimize the entrapment of air caused by over-rolling. Apply material within the recommended thickness range and allow to cure tack free prior to top coating. Do not thin material.
Epoxy.com Product #461 Ultra High Solids Aliphatic Urethane must be aggressively sanded prior to application of a second topcoat.
Epoxy.com Product #461 Ultra High Solids Aliphatic Urethane is a moisture cure urethane, relative humidity will significantly affect cure speed. Refer to Installation Instructions document for important additional details.
Clean Epoxy.com Product #461 Ultra High Solids Aliphatic Urethane off skin with soap and water. Tools and equipment should be cleaned with xylene or lacquer thinner.
Epoxy.com Product #461 Ultra High Solids Aliphatic Urethane will yield 2.9-3.2 mils dry film thickness when spread at 450-500 ft2 per gallon.
Epoxy.com Product #461 Pigmented will yield 3.0-3.3 mils dry film thickness when spread at 450-500 ft2 per gallon.
Epoxy.com Product #461 Ultra High Solids Aliphatic Urethane is available in Clear (gloss or satin) with optional Urethane Pigment Packs in
Epoxy.com Urethane Standard Colors or custom colors subject to lab approval and minimum quantities.
|Hardness(ASTM D 3363 Pencil)||2H to 3H|
|Abrasion Resistance ASTM D 4060||(Taber Abraser 1000 gm. load per wheel)||10-20 mgs./1000 cycles, CS-17 Wheel|
|Solids Content ||(by volume) ||90% Clear|
|Volatile Organic Content (VOC)||100 g/L|
| VOC Compliant in all U.S. states, except Los Angeles SCAQMD counties|
|Dry Film Thickness ||2.8-2.9 mils @ 500 square feet per gallon application thickness
CURE/DRY TIME (Applied at 450-500 square feet per gallon)
|Pot Life||2 hours @ 75°F, 50% RH|
|Re-Coat (must sand first coat) ||8-10 hours @ 75°F, 50% RH|
|Light Service (foot traffic)|| 16-24 hours @ 75°F, 50% RH|
|General Service (vehicle traffic)|| 72+ hours* @ 75°F, 50% RH|
*varies by temp and RH
|Full Cure and Maximum
Resistance to Staining|| 5-7 days* @ 75°F, 50% RH|
*varies by temp and RH
Epoxy.com Product #461 Ultra High Solids Aliphatic Urethane is easily cleaned with neutral soaps or detergents.
|Brake Fluid ||R|
|Citric Acid-30% ||R|
|Citric Acid-40% ||L|
|Crude Oil ||R|
|Diesel Fuel ||R|
|Ethylene Glycol ||R|
|Fatty Acids ||L|
|Hydrochloric Acid-15% ||R|
|Lactic Acid-15% ||R|
|Methyl Ethyl Ketone ||L|
|Nitric Acid-10% ||R|
|Orange Juice ||R|
|Phosphoric Acid-85% ||L|
|Sodium Hydroxide-50% ||R|
|Sulfuric Acid-20% ||R|
|R-Recommended for continuous service.|
|L-Limited Recommendation, occasional spills with frequent cleaning.|
|*-May cause slight stain or discoloration.|
Proper mixing and installation is critical to the optimal success
of all product. See
MSDS for more details on our products.
Be sure to contact us with any questions and/or concerns that you
For more information please contact:
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Florida & Vermont
Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order Status
Katey Fontaine, VP - Customer Service Director
352-533-2167 Norm Lambert, President - Technical Support Director
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
352-489-1625 Fax line to all Departments
24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
|| We accept MasterCard, Visa, American Express, Discover,
or Wire Transfers.|
Copyright © 1994-2013 EPOXY.COM
a division of Epoxy Systems, Inc. -
Florida and Vermont. All rights reserved.
other wise agreed upon in writing, buyer is responsible for the cost of
information is presented in good faith to assist in determining whether this
product is suitable for application. No warranty or representation, however, is
intended or made, nor is protection from any law or patent to be inferred, and
all patent rights reserved.
division of Epoxy Systems, Inc. warrants its products (when
properly stored) for the period of time as follows: Epoxies, Product
#315, Product #315BC, and Product #316 one (1) year; Polyesters,
Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months;
Power Tools and Equipment 90 days; Vinyl Esters, and all other
resins (not specifically mentioned above) 30 days; hand tools
(non-power tools) 30 days. Epoxy.com warrants that its
products will be free of manufacturing defects and will be in
conformity with published specifications when handled, stored, mixed
and applied in accordance with recommendations of Epoxy.com. If any
product fails to meet this warranty, the liability of Epoxy.com will
be limited to replacement of any non-conforming material if notice
of such non-conformity is given to Epoxy.com within the warranty
period for the material (as indicated above), or within 1 year of
the delivery of materials (whichever is sooner). Epoxy.com may in
its discretion refund the price received by Epoxy.com in lieu of
replacing the material. No customer, distributor, or representative
of Epoxy.com is authorized to change or modify the published
specifications of this warranty in any way. No one is authorized to
make oral warranties on behalf of Epoxy.com. In order to obtain
replacement or refund the customer must provide written notice
containing full details of the non-conformity. Epoxy.com reserves
the right to inspect the non-conforming material prior to
replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE
ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE
OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD
PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER
DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All
quotes and sales subject to availability.
Many of our
products are made on an individual order basis. Unless
authorized in writing by Epoxy.com a division of Epoxy Systems, Inc.
in writing before the material is made, there are no returns on
items purchased from us, once the order has been processed, and the
material made. In the event of authorized returns a restocking
charge will be charged in the amount of 30% of the value of the
material returned or $150 whichever is greater. No returns on
non-list priced items. All Returns are for merchandise (store)
credit only, no cash or credit card credits. In the event of a
return, buyer is responsible for the cost of shipping and handling
in both directions.
[Catalog of Products]
[Where to Start]
[Elastomeric Polyurethane Systems]
[Epoxy Resin Systems]
[Seamless Garage Floors]
[High Temperature Epoxy]
[Joint Systems / Sealants]
[Methyl Methacrylate (MMA)]
[Mortars / Grouts]
[Who We Are]
[Tech Data Sheets in Acrobat Format]
[MSDS in Acrobat Format]
[Online Ordering Authorization Form]
[Add this page to Favorites]