Epoxy Oil Stop Primer - For Oil Saturated Concrete
Penetrating Deeply into Oil Saturated Concrete to Lock Down Oil Leaving a Clean Surface
Epoxy.com Product #201
GENERAL DESCRIPTION
Epoxy.com Product #201 Epoxy Oil Stop Primer - For Oil Saturated Concrete is a two component, epoxy-amine undercoating
designed to be compatible with petroleum based oil and greases. In many instances
petroleum can penetrate the surface of concrete floors to the extent that the oil may not
be removed by surface cleaning. If untreated, this oil may migrate back to the surface to
cause a delamination.
Epoxy.com Product #201 Epoxy Oil Stop Primer - For Oil Saturated Concrete mixes with the oil in the surface,
penetrating deeply to tie up and lock in contamination leaving a clean surface for
application of epoxy flooring and coating resins.
APPLICATIONS
Epoxy.com Product #201 Epoxy Oil Stop Primer - For Oil Saturated Concrete is suited as a primer for most Epoxy.com
epoxy based products where petroleum oil based contamination cannot be fully removed.
Among these applications are the following:
- Assembly Plants
- Bakeries
- Basement Floors
- Bottling Plants
- Break Rooms
- Cafeterias
- Canning Plants
- Car Washes
- Cells
- Chemical Storage Areas
- Chemical Processing Areas
- Church Floors
- Classroom Floors
- Corridors
- Educational Facilities
- Entrances
- Food Plants
- Fork Lift Areas
- Health Care Facilities
- Hospitals
- Kennels
- Kitchens
- Laboratories
- Law Enforcement Facilities
- Laundries
- Leveling concrete
- Loading docks
- Locker Rooms
- Machine Shops
- Manufacturing Areas
- Marine Surfaces
- Meat Preparation Areas
- Mortuaries
- Nuclear Plant Floors
- Offices
- Oil Storage and Processing Facilities
- Patching concrete
- Photography Processing Areas
- Power Plants
- Printing Plants
- Produce Preparation Areas
- Pool Decks
- Ramps
- Research Facilities
- Rest Rooms
- Restaurants
- Secondary Containment Structures
- Semiconductor Plants
- Sewer Plants
- Shop Floors
- Shopping Centers
- Shower Rooms
- Store Floors
- Show Rooms
- Supermarkets
- Veterinary Facilities
- Water Plants
- Warehouses
- many others
ADVANTAGES
- Bonds through petroleum based grease oil
- No need to chip out surface
- Preserves concrete
SURFACE PREPARATION
Concrete should be thoroughly degreased and solvent washed.
Create a profile with a wire brush, scarifying, or abrasive blast. As much of the oil
should be removed as possible. Surface must be sound. All loose or soft concrete must be
removed.
MIXING INSTRUCTIONS
Temperature of Epoxy.com Product #201 Epoxy Oil Stop Primer - For Oil Saturated Concrete must be 60°F or above at time of
mixing. Stir each component separately before blending. Pour Part A into a clean container
and add Part B Stir for three minutes with a low speed electric drill motor equipped
with a mixing paddle. Immediately begin application.
APPLICATION
Epoxy.com Product #201 Epoxy Oil Stop Primer - For Oil Saturated Concrete can be applied with brush, or 3/8" nap roller.
Apply Epoxy.com Product #201 Epoxy Oil Stop Primer at a rate of 200-320 SF per
gallon. Be sure to install your next coat within 24 hours. If for some
reason that is not possible be sure to sand off all shine and damp wipe with
xylene before recoating.
For more information before installing please see Epoxy.com
installation tips at
http://www.epoxy.com/install.htm.
DRY TIME
Epoxy.com Product #201 Epoxy Oil Stop Primer - For Oil Saturated Concrete will normally be ready to recoat in 8-10
hours. Top-coating before 8 hours can cause some slight bleeding of the Epoxy.com Product #201 Epoxy Oil Stop Primer into
the topcoat. For best results 16-24 hours should be given.
LIMITATIONS
Before application of Epoxy.com Product #201 Epoxy Oil Stop Primer - For Oil Saturated Concrete, New concrete should be at least 28 days old. Temperature of
substrate must be between 50°F and 90°F. DO NOT thin. Be sure to install
your next coat within 24 hours. If for some reason that is not possible be
sure to sand off all shine and damp wipe with xylene before recoating. For outdoor use contact Epoxy.com for technical assistance.
SAFETY PRECAUTIONS
Prolonged or repeated exposure may cause eye and skin
irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses
with side shields and wear protective rubber gloves.
CLEANING
All tools and equipment should be cleaned before the system
gels. Use MEK, Acetone, or any lacquer solvent.
APPLICATION PROPERTIES @77° F |
| Mix Ratio |
1:1 By Volume |
| Solids by weight |
69.5% (min.) |
| Pot Life (200 gr.) |
4-6 hours |
| Tack Free |
2-4 hours |
| Cure Time - Recoat |
4-8 hours |
| Cure Time - Light Traffic |
16-24 hours |
| Final Cure |
2-7 Days |
| V.O.C. - Part A |
2.5 lb. / gallon |
| V.O.C. - Part B |
2.75 lb. / gallon |
| Recommended Thickness |
5-8 mils per coat (wet) |
| Theoretical Coverage per gallon |
200-320 square feet |
| Shelf life |
1 Year (min) |
| Color |
Black only |
| Packaging (unit size) |
4 gal. Units (2 gal. A and 2 Gal. B) |
PHYSICAL PROPERTIES |
| Finish Characteristics (gloss at 60 degrees - Erichsen glossmeter) |
40-60 |
| Abrasion Resistance (Taber CS-17 – wheel 1000 gram with 500 cycles) |
0.037 gram loss |
| Impact Resistance (Gardner impact, direct = 50 inch lb.) |
PASSED |
| Shore D Hardness |
69 |
| Flexibility (no cracks on a 1/8" mandrel) |
PASSED |
Other Epoxy.com Primers
Other customers who visited this page also visited:
Add this page to Favorites!
|