Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Epoxy Joint Filler

Epoxy Joint Filler for Saw Cut Expansion Joints

 100% Solids Zero (0) VOC Epoxy Resin

Epoxy.com Product #11


Epoxy Joint Filler for Saw-Cut Control Joints Product #11 is a 100% solids zero (0) VOC, flexible epoxy joint filler for saw-cut joints of concrete slabs on grade, or to repair existing slabs.  Epoxy.Saw-Cut Control Joint Filler Product #11 absorbs the impact and shock of heavy loads and steel wheeled traffic, preventing erosion of control joint edges.

ADVANTAGES of EPOXY JOINT FILLER

  • High elongation
  • Flexibility provides for joint movement
  • Protects slabs edges from chipping
  • Cures on damp or wet surfaces
  • Field proven reliability
  • Good shock absorption qualities
  • Zero (0) VOC so it meets even the strictest Low VOC standards

SURFACE PREPARATION EPOXY SAWCUT RESIN

Surface to receive Epoxy Joint Filler for Saw-Cut Control Joints Product #11 must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, or mechanical abrasion. Remove water and dust from all surfaces with an oil-free blast immediately prior to application.

MIXING INSTRUCTIONS EPOXY RESIN + HARDENER

Temperature of Epoxy Joint Filler for Saw-Cut Control Joints Product #11 must be 50 degrees F or above at time of mixing. Stir each component separately before blending. Mix one part by weight of Part A with one part by weight of Part B for three minutes with a low speed electric drill motor equipped with a mixing paddle.

APPLICATION - EPOXY SAWCUT JOINT RESIN

wpe24096.gif (7834 bytes)

For application on flat surfaces Epoxy Joint Filler for Saw-Cut Control Joints Product #11 can be poured. For vertical surfaces Epoxy Joint Filler for Saw-Cut Control Joints Product #11can be thickened with Product #71. Contact Epoxy.com for more information on the thickening process. This mix of Epoxy Joint Filler for Saw-Cut Control Joints Product #11 & Epoxy.com Product #71 can be applied by power or hand operated caulking gun, by trowel, or with a putty knife, or pumped from one of Epoxy.com' Binary Pumping Systems. In areas where cosmetics are important mask both sides of the substrate before applying the material.

LIMITATIONS - EPOXY JOINT RESIN

Use of solvents for thinning will prevent proper cure. Epoxy Joint Filler for Saw-Cut Control Joints Product #11 should not be installed on new concrete floors until maximum shrinkage has occurred. Generally speaking, this time period is a minimum of 28 days.

Safety Precautions

Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.

Cleaning

All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent.

APPLICATION PROPERTIES @77°F

Mix Ratio 1:1 By Volume
Viscosity (mixed) 2,200 CPS
Gel Time 30 minutes
Consistency Pourable liquid
Initial Cure 8 Hours (80% strength)
Final Cure 2-3 Days
Packaging (unit size) 2 gallon per units, 10 gallon per unit
Standard Colors Light Gray, Dark Gray
Shore A. Hardness 70 to 80
VOC Content (grams/liter) 0.0 (Zero)

PHYSICAL PROPERTIES

Artificial Weathering
(ASTM G23-75 Type D)
10-15% elastomeric property
change after 1000 hours
Bond Cohesion after Water Immersion
(Fed. Spec TT-S-00227E)
No Failure after 25% total movement
Tensile Strength (ASTM D-638) 600 p.s.i
Ultimate Elongation (ASTM D-638) 35%
Tear Resistance (ASTM D-624-73) 20 lb./in
Service Temperature 30 degrees F. to 180 ° F.

Proper mixing and installation is critical to the optimal success of all products.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
A Vermont Corporation
USA

We have products that have passed the test of time as well as the best new Systems available today.

Since 1980 - 40 years of the highest quality products

Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time)

Closed for lunch from 12Noon to 1PM


321-206-1833  Customer Service - Ordering and Order Status
                         Katey Lambert-Fontaine, VP - Chief Operations Officer
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO

Copyright © 1994-2023 (providing online information about the right product for the right job for nearly 30 years)  EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks
We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.