Epoxy Gel Super Fast Cure
Product #2704
DESCRIPTION
Epoxy Gel Super
Fast Cure Product #2704 is a fast setting, 100% solids epoxy crack
gel and filler used to line, patch, or repair floor and
wall surfaces. Epoxy Gel Super Fast Cure Product #2704 is the ideal material for repair of surfaces
damaged from environmental or chemical attack. Epoxy Gel Super Fast
Cure Product #2704 can also be
used as a base material beneath coating, slurry, and mortar systems to repair
before coating.
ADAVANTAGES
- Easy 1 to 1 Mixing Ratio.
- Putty Consistency
Provides Easy Application.
- Low Odor During Application and Cure-Can be Used in
Occupied Facilities.
- Can be Used in Both Interior and Exterior Applications.
- Fast Set Provides Rapid Turn Around.
CONSIDERATIONS
- Substrate temperature
must be a minimum of 50°F.
- Substrate must be free of dirt, waxes, curing
agents, and other foreign materials.
- Should not be installed on new concrete
(at least 30 days after placement).
- Should not be used where a flexible joint
repair material is required.
COMPOSITION
100% Solids Epoxy Resin with Aliphatic
Amines
APPLICATION SURFACE PREPARATION
Surface Preparation is the most critical
portion of any successful resinous flooring system application. All substrates
must be properly prepared as outlined in Epoxy.com
Surface Preparation Procedures. The Epoxy.com technical service department is available to
answer any questions.
MIXING & INSTALLATION
Epoxy Gel Super Fast
Cure Product #2704 is mixed by combining equal parts by volume
of Part A and Part B. Mix until a consistent color is reached. Small
amounts of Epoxy Gel Super Fast Cure Product #2704 can be mixed on a
mortar board using a spatula. Epoxy Gel Super Fast Cure Product #2704 is
installed using a trowel, spatula, or knife. For complete installation
instructions, contact Epoxy.com Technical Support.
CLEAN UP
Clean skin
with soap and water. Tools and equipment should be cleaned with xylene or
lacquer thinner before Epoxy Gel Super Fast Cure Product #2704 gels.
COVERAGE
Coverage of Epoxy Gel Super Fast Cure Product #2704 varies with
application. One gallon contains approximately 231 cubic inches. So you
will get about 25.6 square feet per 1/16 inch of thickness.
TECHNICAL DATA
| Mixed Consistency |
Putty |
| Mixing Ratio |
1 Part A to 1 Part B by Volume |
| Solids Content |
100%, by volume |
| Volatile organic Content (VOC) |
-0- |
| Color |
Grey (when mixed) |
| Weight per gallon |
8.5-9.0 pounds per gallon mixed |
CURE/DRY
TIME @ 75°F
| Pot Life |
5-7 minutes |
| Dry to Touch |
30-45 minutes |
| Re-Coat |
1-1.5 hours |
| Sanding Time |
2 hrs |
| Full Cure & Maximum Resistance |
5 days |
PHYSICAL PROPERTIES
| Tensile Strength (ASTM D638) |
8,500 psi |
| Adhesion to Concrete (ACI Comm 403) |
350 psi (100% Concrete Failure) |
| Hardness (ASTM D-2240) |
80 (Shore D) |
| Flexural Strength (ASTM D-790) |
8,000 psi |
| Compressive Strength (AST D-695) |
11,000 psi |
| Service Temperature |
150°F (wet) 160°F (dry) |
| Water Absorption (ASTM D670-73) |
0.10% maximum |
AVAILABILITY
Contact Epoxy.com Ordering Department at 321-206-1833
MAINTENANCE
Epoxy Gel Super Fast Cure Product #2704 is typically installed as a base
material beneath Epoxy.com Flooring Systems. However, if needed, Epoxy
Gel
Super Fast Cure Product #2704 is
easily cleaned with neutral soaps or detergents. Routine mechanical scrubbing is
recommended for all surfaces having a non-skid texture.
TECHNICAL SERVICE
Epoxy.com provides services and consultations on material
selection, specification, troubleshooting, and other information on the
proper repair and protection of concrete surfaces. Epoxy.com Sales
Representatives and Epoxy.com Technical Services are available to assist
you. Call: 352-533-2167 or visit www.Epoxy.com.
BLOG POSTS & NEWS
You can find more information on
Epoxy Gel Adhesive Products, and many of our other products at
news.epoxy.com.
|