FAST SETTING FLEXIBLE EPOXY JOINT SEALANT
Hard to Touch Joint Sealed in 1 Hour
Epoxy.com Product #2011
Product #2011 Low Modulus Fast Set Epoxy Gel is a two component 100% solids
polymer system designed for applications where a resilient joint material is
needed. The two component material (standard) is supplied with a gray component
and a clear component. Product #2011 was developed for plural
component pump equipment, and is available in cartridge units.
Product #2011 Low Modulus Fast Set Epoxy Gel is recommended for concrete/cement expansion joints in general industry.
Not recommended for applications for all acids and chemicals.
None required. Many epoxies and urethane are compatible.
- Color stability may be affected by environmental conditions such
as high humidity, chemical exposure or exposure to certain types of light such
as sodium vapor lighting.
- Colors may vary from batch to batch.
- Gray color is
not from our standard color chart.
- Substrate temperature must be 5�F above dew
- All new concrete must be cured for at least 30 days prior to application
- This product must be mixed well.
- Apply sample installation at an off-sight
location before using material in a commercial setting to become familiar with
- Product is not UV color stable.
- This product was developed for plural component mixing equipment so
you may want to purchase in binary tube sets, unless you have that kind
- Test data based on neat resin.
- Physical properties are typical
values and not specifications.
MIXING AND APPLICATION INSTRUCTIONS
Product #2011 Low Modulus Fast Set Epoxy Gel in an area so as to bring the material
to normal room temperature before using. Continuous storage should be between
50-90�F. Avoid low temperatures and large temperature fluctuations in storage as
these conditions could cause possible product crystallization.
All dirt, oil, dust, foreign contaminants and laitance must be
removed to assure a trouble free bond to the substrate. We recommend that all
loose concrete, previous joint compound or other foreign material be removed to
leave a clean sound joint at least 2� deep. For best results, edges should be sawcut and a one inch backer rod should be placed into the joint leaving
approximately 1 to 1 1/2 inches from the top of the backer rod to the top of the
No primer is necessary. This material is self priming.
However, any suitable primer can be used.
It is important
that tProduct #2011 Low Modulus Fast Set Epoxy Gel be mixed well. Improper mixing will cause an incomplete cure
and soft spots in the joint. Mix one part by volume part A to one part by volume
of part B. This product has a very short pot life of 1-2 minutes and should be
applied using plural component pump equipment using a 3/8� diameter 40 element
tip. ALWAYS dispense a small beginning portion onto cardboard to prevent
non-mixed material from entering joint. Improper mixing may result in product
Discard the unmixed portion of mixed
Product #2011 Low Modulus Fast Set Epoxy Gel
at the start of each application. This product has a very short pot life of 1-2
minutes and should be applied using plural component pump equipment or dispensed
with a dual cartridge caulking gun using a 3/8� diameter 40 element tip.
The product in dual cartridges are available from Epoxy.com. Make
sure the material applied is uniform in color which would indicate the product
is mixed well. If marbling occurs, review your application equipment to
ascertain if it will correctly mix the material.
Apply the mixed
Product #2011 Low Modulus Fast Set Epoxy Gel by
pumping the mixed material into the expansion joint to be repaired. Remove any
excess material with a putty knife or similar tool after the material has set up
enough to cut through with a razor scraping toll. Maintain temperatures within
the recommended ranges during the application and curing process. When
temperatures are lower, allow more time for this material to cure.
No recoating or topcoating is necessary. However, if you opt to
topcoat the applied joint compound, allow it to cure before topcoating. It is
not necessary to prime over the joint compound prior to topcoating the joint
compound. Many epoxies and urethanes can be used. In some instances, especially
when excessive expansion joint movement is involved, topcoats may chip or crack.
However, most epoxy or topcoat products will adhere to the joint compound very
Caution! Some cleaners may
affect the color of the floor installed. Test each cleaner in a small area,
utilizing your cleaning technique. If no ill effects are noted, you can continue
to clean with a product and process tested.
Restrict the use of
the floor to light traffic and non-harsh chemicals until the coating is fully
cured (see technical data under full cure). It is best to let the floor remain
dry for the full cure cycle.
|SOLIDS BY WEIGHT
|VOLATILE ORGANIC CONTENT
||0 lb per gallon
|| Medium gray (mixed) Part A is gray and
Part B is clear
||1/2� to 1 1/2�
||2 gallon kit @ 1/2� by 1.0� yields 74-78
||2 gallon kit 0.265 (approx) 10 gallon kit 1.325
||1 to 1 by volume
||6 months in unopened containers properly
normal room temperature. (mix before use)
||40-45 Shore D
|ELONGATION AT BREAK
||18.2 mg loss with a 1000 gram total load at
1000 revolutions with a CS17 wheel
||410 psi (elcometer) � no
||Mixed= 1,200 cps � 1,400 cps (typical)
||Part A �not regulated� Part B �not
CURE SCHEDULE (70�)
|recoat or topcoat
|light foot traffic
|full cure (heavy traffic)
|10% sodium hydroxide
|50% sodium hydroxide
|10% sulfuric acid
|70% sulfuric acid
|10% HC1 (aq)
|5% acetic acid
| Rating key:
A - not recommended,
B - 2 hour term splash spill,
C - 8 hour term splash spill,
D - 72 hour immersion,
E - long term immersion.
NOTE: extensive chemical resistance information is
Epoxy.com Technical Support.
NOTICE TO BUYER
DISCLAIMER OF WARRANTIES AND
LIMITATIONS ON OUR LIABILITY
You can find more information on
Polyurethane Products, and many of our other products at
We warrant that our products are manufactured to
strict quality assurance specifications and that the information supplied by us
is accurate to the best of our knowledge. Such information supplied about our
products is not a representation or a warranty. It is supplied on the condition
that you shall make your own tests to determine the suitability of our product
for your particular purpose. Any use or application other than recommended
herein is the sole responsibility of the user. Listed physical properties are
typical and should not be construed as specifications.
NO WARRANTY IS MADE,
EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS
BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE,
EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT
SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF
SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT.
We shall have
no liability for incidental or consequential damages, direct or indirect. Our
liability is limited to the net selling price of our product or the replacement
of our product, at our option. Acceptance of delivery of our product means that
you have accepted the terms of this warranty whether or not purchase orders or
other documents state terms that vary from this warranty. No representative is
authorized to make any representation or warranty or assume any other liability
on our behalf with any sale of our products. Our products contain chemicals that
may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA
SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.