Epoxy.com' Product #11100% Solids Epoxy Joint FillerEpoxy.com Product #11 Saw-Cut Control Joint Filler is a 100% solids flexible epoxy joint filler for saw-cut joints of concrete slabs on grade, or to repair existing slabs. Epoxy.com Product #11 Saw-Cut Control Joint Filler absorbs the impact and shock of heavy loads and steel wheeled traffic, preventing erosion of control joint edges. ADVANTAGES
SURFACE PREPARATIONSurface to receive Epoxy.com Product #11 Saw-Cut Control Joint Filler must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, or mechanical abrasion. Remove water and dust from all surfaces with an oil-free blast immediately prior to application. MIXING INSTRUCTIONSTemperature of Epoxy.com Product #11 Saw-Cut Control Joint Filler must be 50 degrees F or above at time of mixing. Stir each component separately before blending. Mix one part by weight of Part A with one part by weight of Part B for three minutes with a low speed electric drill motor equipped with a mixing paddle. APPLICATION
For application on flat surfaces Epoxy.com Product #11 Saw-Cut Control Joint Filler can be poured. For vertical surfaces Epoxy.com Product #11 Saw-Cut Control Joint Filler can be thickened with Product #71. Contact Epoxy.com for more information on the thickening process. This mix of Epoxy.com Product #11 & Epoxy.com Product #71 can be applied by power or hand operated caulking gun, by trowel, or with a putty knife, or pumped from one of Epoxy.com' Binary Pumping Systems. In areas where cosmetics are important mask both sides of the substrate before applying the material. LIMITATIONSUse of solvents for thinning will prevent proper cure. Epoxy.com Product #11 Saw-Cut Control Joint Filler should not be installed on new concrete floors until maximum shrinkage has occurred. Generally speaking, this time period is a minimum of 28 days. Safety PrecautionsProlonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves. CleaningAll tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent.
CoverageChart is based on the relationship between the 231 cubic inches in a US gallon and the dimensions of the joint. Coverage is per gallon
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments Website: www.epoxy.com 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2010 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products]
[Where to Start] [[Bonding Systems]
[Chip Floors] [Chemical Resistance]
|
