Epoxy.com Product #201Epoxy Oil Stop Primer - For Oil Saturated ConcretePenetrating Deeply into Oil Saturated Concrete to Tie Up and Lock in In - Leaving a Clean SurfaceGENERAL DESCRIPTIONEpoxy.com Product #201 Epoxy Oil Stop Primer - For Oil Saturated Concrete is a two component, epoxy-amine undercoating designed to be compatible with petroleum based oil and greases. In many instances petroleum can penetrate the surface of concrete floors to the extent that the oil may not be removed by surface cleaning. If untreated, this oil may migrate back to the surface to cause a delamination. Epoxy.com Product #201 Epoxy Oil Stop Primer - For Oil Saturated Concrete mixes with the oil in the surface, penetrating deeply to tie up and lock in contamination leaving a clean surface for application of epoxy flooring and coating resins. APPLICATIONSEpoxy.com Product #201 Epoxy Oil Stop Primer - For Oil Saturated Concrete is suited as a primer for most Epoxy.com epoxy based products where petroleum oil based contamination cannot be fully removed. Among these applications are the following:
ADVANTAGES
SURFACE PREPARATIONConcrete should be thoroughly degreased and solvent washed. Create a profile with a wire brush, scarifying, or abrasive blast. As much of the oil should be removed as possible. Surface must be sound. All loose or soft concrete must be removed. MIXING INSTRUCTIONSTemperature of Epoxy.com Product #201 Epoxy Oil Stop Primer - For Oil Saturated Concrete must be 60°F or above at time of mixing. Stir each component separately before blending. Pour Part A into a clean container and add Part B Stir for three minutes with a low speed electric drill motor equipped with a mixing paddle. Immediately begin application. APPLICATIONEpoxy.com Product #201 Epoxy Oil Stop Primer - For Oil Saturated Concrete can be applied with brush, or 3/8" nap roller. DRY TIMEEpoxy.com Product #201 Epoxy Oil Stop Primer - For Oil Saturated Concrete will normally be ready to recoat in 8-10 hours. Top-coating before 8 hours can cause some slight bleeding of the Epoxy.com Product #201 Epoxy Oil Stop Primer into the topcoat. For best results 16-24 hours should be given. LIMITATIONSBefore application of Epoxy.com Product #201 Epoxy Oil Stop Primer - For Oil Saturated Concrete, New concrete should be at least 28 days old. Temperature of substrate must be between 50°F and 90°F. DO NOT thin. For outdoor use contact Epoxy.com for technical assistance. SAFETY PRECAUTIONSProlonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves. CLEANINGAll tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent.
Other Epoxy.com Primers
| ||||||||||||||||||||||||||||||||||||||||||
|
Proper mixing and installation is critical to the optimal success of all product. See Installation Tips, Techdata, & MSDS for more details on our products. Be sure to contact us with any questions and/or concerns that you have. For more information please contact: Epoxy.com Office Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time). 321-206-1833 Customer Service - Ordering and Order Status 714-657-3826 Technical Support 352-489-1625 Fax line to all Departments Website: www.epoxy.com 24 hour Hazmat Emergency Telephone Response Service -1-800-633-8253
Copyright © 1994-2010 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved. Unless other wise agreed upon in writing, buyer is responsible for the cost of shipping. This information is presented in good faith to assist in determining whether this product is suitable for application. No warranty or representation, however, is intended or made, nor is protection from any law or patent to be inferred, and all patent rights reserved. Epoxy.com a division of Epoxy Systems, Inc. warrants its products (when properly stored) for the period of time as follows: Epoxies, Product #315, Product #315BC, and Product #316 one (1) year; Polyesters, Methyl Methacrylates (normal) two (2) months and Polyurethanes Four (4) months; Power Tools and Equipment 90 days; Vinyl Esters, High Molecular Weight Methacrylates (HMMA) and all other resins (not specifically mentioned above) 30 days; hand tools (non-power tools) 30 days. Epoxy.com warrants that its products will be free of manufacturing defects and will be in conformity with published specifications when handled, stored, mixed and applied in accordance with recommendations of Epoxy.com. If any product fails to meet this warranty, the liability of Epoxy.com will be limited to replacement of any non-conforming material if notice of such non-conformity is given to Epoxy.com within the warranty period for the material (as indicated above), or within 1 year of the delivery of materials (whichever is sooner). Epoxy.com may in its discretion refund the price received by Epoxy.com in lieu of replacing the material. No customer, distributor, or representative of Epoxy.com is authorized to change or modify the published specifications of this warranty in any way. No one is authorized to make oral warranties on behalf of Epoxy.com. In order to obtain replacement or refund the customer must provide written notice containing full details of the non-conformity. Epoxy.com reserves the right to inspect the non-conforming material prior to replacement. EXCEPT FOR THE EXPRESSED WARRANTY STATED ABOVE, THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PURPOSE. Epoxy.com 'S OBLIGATION SHALL NOT EXTEND BEYOND THE OBLIGATIONS EXPRESSLY UNDERTAKEN ABOVE AND Epoxy.com SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OR ANY THIRD PARTY FOR ANY LOSS, COST, EXPENSE, DAMAGE OR LIABILITY, WHETHER DIRECT OR INDIRECT, OR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. All quotes and sales subject to availability. Many of our products are made on an individual order basis. Unless authorized in writing by Epoxy.com a division of Epoxy Systems, Inc. in writing before the material is made, there are no returns on items purchased from us, once the order has been processed, and the material made. In the event of authorized returns a restocking charge will be charged in the amount of 30% of the value of the material returned or $150 whichever is greater. No returns on non-list priced items. All Returns are for merchandise (store) credit only, no cash or credit card credits. In the event of a return, buyer is responsible for the cost of shipping and handling in both directions.
[Home] [Catalog of Products]
[Where to Start] [[Bonding Systems]
[Chip Floors] [Chemical Resistance]
|
