|
Chemical Resistant Epoxy Primer
Epoxy Flooring Primer/Sealer and
Fabric Layup Resin for
Composite Materials
Epoxy Mortar Resin
Epoxy.com Product #12
GENERAL DESCRIPTION
Chemical Resistant Epoxy Primer and Epoxy Floor Sealer Product #12 is a two component, seamless 100% solids epoxy primer system with High Chemical Resistance and High Bond Strength. The epoxy may be applied as a primer for most High End Industrial coatings. Product #12 Chemical Resistant Epoxy Primer and Epoxy Floor Sealer is also commonly used as a fabric layup epoxy resin in carbon fiber composite and fiberglass composite materials, and as an epoxy mortar resin.
APPLICATIONS
Chemical Resistant Epoxy Primer and Epoxy Floor Sealer Product #12 can be used as a primer and as a composite fabric layup resin, and an epoxy mortar resin.
ADVANTAGES
- 100% SOLIDS - Gives you excellent economy.
- LOW TO VIRTUALLY NO ODOR
- STRONG YET RESILIENT
- HIGH BOND STRENGTH
- ABRASION RESISTANT
- CHEMICAL RESISTANT
SURFACE PREPARATION
Surface to receive Chemical Resistant Epoxy Primer and Epoxy Floor Sealer Product #12 must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, mechanical abrasion. If acid etching is used follow with abrasive or mechanical abrasion. Remove water and dust from all surfaces with an oil free blast, or vacuum, immediately prior to application.
MIXING INSTRUCTIONS
Temperature of Chemical Resistant Epoxy Primer and Epoxy Floor Sealer Product #12 must be 65 degrees F or above at time of mixing. Stir each component separately before blending. Mix two parts by volume of Part A with one part by volume of Part B for three minutes with a low speed electric drill motor equipped with a mixing paddle.
APPLICATION
Chemical Resistant Epoxy Primer and Epoxy Floor Sealer Product #12 can be applied with brush, roller, trowel, airless sprayer or squeegee. Apply a coat of Product #12 to surface to be finished. Average application rate is 200 square feet per gallon on smooth concrete. Contact Epoxy.com technical support for information on how to adjust application rate to account for a substrate that is more porous, or has more texture.
If anti-skid is required, or to improve trowelablilty of the next coat, it may be broadcast with aggregate (while epoxy is still wet). This can be done by hand or mechanical means. Allow them to dry. Then sweep off excess aggregate. Sand surface (if required) to desired texture. It may be left a final sealer or you may install other high end top-coats over the Product #12 at a rate as recommended by that material.
LIMITATIONS
New concrete to receive PChemical Resistant Epoxy Primer and Epoxy Floor Sealer Product #12 (and epoxy layup resin) should be at least 28 days old. Temperature of substrate must be above 55° F. DO NOT thin. For outdoor use contact Epoxy.com for technical assistance.
SAFETY PRECAUTIONS
Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.
CLEANING
All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent.
APPLICATION PROPERTIES @77° F |
|
| Mix Ratio | 2:1 By Volume |
| Viscosity (mixed) | <500 CPS |
| Pot Life (200 gr.) | 30 minutes |
| Recoat Time | 6-10 hours depending on temperature |
| Maximum Time to Recoat | 24-48 hours depending on temperature |
| Final Cure | 7 Days |
| Packaging (unit size) | gallons, pails, drums |
PHYSICAL PROPERTIES (neat) |
|
| Bond Strength (ASTM C-882) | 2100 psi |
| Flexural Strength (ASTM D-2240) | >6000 psi (7 days) |
| Compressive Strength (ASTM D-695) | >9900 psi (7 days) |
| Absorption (ASTM D-570) | <1% |
| Thermal Shock | 40 Hr. @10° F., 3 Min. @ 212° F. Shock Water @ 33° F. |
For more information please contact:
Epoxy.com
A Division of
Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems
,
Since 1980 - Over 33 years
Florida & Vermont
USA
Customer and Technical Support Hours: 9AM-4PM Eastern Time
(6AM-1PM Pacific Time)
.
Closed 12 Noon-1PM Eastern Time for Lunch
321-206-1833 Customer Service - Ordering and Order
Status
Katey Fontaine, VP - Customer
Service Director
sales@epoxy.com
Technical Support
352-533-2167 Norm Lambert, President - Technical
Support Director
info@epoxy.com
352-489-1666 Accounting and Administration
Debby Lambert, CEO, and CFO
office@epoxy.com
352-489-1625 Fax line to all Departments
|
We accept MasterCard, Visa, American Express, Discover, or Wire Transfers. |
Copyright © 1994-2015 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont. All rights reserved.