Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

CONDUCTIVE EPOXY PRIMER

Epoxy.com Product #668


DESCRIPTION

Product #668 Conductive Epoxy Primer is a water-based, two component, carbon-filled conductive epoxy primer designed for use with various Epoxy.com Conductive Systems. Product #668  has very low odor making it suitable for use in occupied buildings.

ADVANTAGES

  • For Use with Various Epoxy.com Conductive Systems
  • Maintains Electrical Conductivity Performance over the Wear Life of the System
  • Fast Dry Time
  • Low Odor During Application and Cure
  • VOC Compliant in all 50 US States, Meets USGBC LEED Requirements

CONSIDERATIONS

  • Substrate must be above 50°F and relative humidity below 85% for proper curing.
  • Substrate must be properly prepared following Epoxy.com recommendations and free of dirt, waxes, curing agents and other foreign materials
  • Excessive moisture in the substrate will require a moisture vapor control treatment like Product #830
  • Concrete substrate must be insulated with a non-conductive epoxy primer/basecoat like Product #12 Chemical Resistant Epoxy Primer or Product #899 Epoxy Primer  prior to application of Product #668 Conductive Epoxy Primer. Consult with Epoxy.com Technical Department for recommendations.
  • Must be topcoated with a conductive topcoating like Product #1ESD, or Product #630 Conductive

APPLICATION

SURFACE PREPARATION

Surface Preparation is the most critical portion of any successful resinous flooring system application. All substrates must be properly prepared and tested for moisture as outlined in installation proceedures or as recommended by Epoxy.com.

BATCHING, MIXING & INSTALLATION

 

Product #668 Conductive Epoxy Primer:
PART A 1 quart to
PART B 3 quarts to
Clean Water 8 volume ounces (6% by volume of water)
Total 4.125 quarts

Coverage (250 square feet/gal.) 265.6 square feet per batch

Pre-mix Product #668 Conductive Epoxy Primer  part B prior to combining with part A. Mix 1 part A with 3 parts B for 2-3 minutes with a low-speed jiffy mixer, scraping sides and bottom of mix vessel. Continue mixing and add 6% by volume clean potable water and continue mixing for 1 additional minute.

Immediately spread and backroll mixed Product #668 Conductive Epoxy Primer at a rate of 250 ft2 per gallon with a short nap roller over previously applied non-conductive epoxy primer/basecoat. Care should be taken to avoid puddles. Allow to cure minimum 12 hours (at 75°F) to maximum 24 hours before coating with specified topcoat.

Important: Test Product #668 Conductive Epoxy Primer with ohm meter prior to topcoating to confirm acceptable level of conductivity is achieved. If test readings are higher than 25,000 ohms, contact Epoxy.com Technical Support Department for further instructions before installing specified topcoat.

Top Coat with a conductive topcoating like  Product #1ESD, or Product #630 Conductive

CLEAN-UP

Clean skin with soap and water. Tools and equipment should be cleaned with warm soapy water, xylene or lacquer thinner. Consult Material Safety Data for safety and health precautions.

COMPOSITION

Waterborne Epoxy Resin and Conductive Filler. Color: Black.

COVERAGE

Product #668 Conductive Epoxy Primer applied at 250 ft2 per gallon yields 2.7 mils dry film thickness.

TECHNICAL DATA (@ 75°F, 50% RH)

Viscosity 500-1000 CPS
Mixing Ratio 1 Part A to 3 Parts B by Volume
Solids Content, by volume 45%, thinned
Volatile Organic Content (VOC) <10 g/L
Bond Strength to Concrete 300-400+ psi (100% concrete failure)
Shelf Life 6 months when properly stored

CURE/DRY TIME (@ 75°F, 50% RH)

Pot Life 20-30 minutes
Dry to Touch 6-8 hours
Recoat (Refer to testing requirements) 12-24 hours
Light Traffic 24 hours

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems,
Since 1980 - 35 years
Florida & Vermont
USA


Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12 Noon-1PM Eastern Time for Lunch

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Fontaine, VP - Customer Service Director
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

Get important hint, tips, tricks, and product information:  Visit our Blog, and join us on Facebook and Twitter.

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks

Copyright © 1994-2017 - Epoxy Systems Inc. DBA Epoxy.com  - Commercial, Industrial, and Residential Resins Since 1980

/