Epoxy Polyurethane Polyester MMA - Methyl Methacrylate, other Resin Systems Over 350 Products Since 1980 Contact Us

Pigmented Epoxy Mortar

Epoxy Mortar Binder Resin100% Solids Zero VOC

Epoxy.com Product #24


DESCRIPTION

Pigmented Epoxy Mortar Resin Product #24 is a multipurpose colored epoxy binder for Epoxy Mortar Systems. This all purpose epoxy resin is characterized as an excellent general purpose material with good clarity and color retention. It is essentially odorless and can therefore be used in occupied areas. Pigmented Epoxy Mortar Resin Product #24 is 100% solids and has Zero (0) VOC, so it meets event the strictest low VOC standards.

ADVANTAGES

Epoxy.com Product #24 Pigmented Epoxy Mortar used on a the bathroom floor a a dorm at UVM in Burlington, Vermont
  • Good troweling properties
  • Excellent color retention
  • Low odor for Good troweling properties
  • Excellent color retention

CONSIDERATIONS

  • Minimum application temperature of 50°F (Contact Epoxy System, Inc. for Low Temperature Cure)
  • .
  • Substrate must be free of curing agents and any foreign materials.
  • Slight color variation can be expected from batch to batch.
  • Pigmented version should not be used as a coating.

COMPOSITION

100% solids amine cured Epoxy Resin and Epoxy Hardener.

APPLICATION

SURFACE PREPARATION

Surface Preparation is the most critical portion to any successful resinous flooring system application. All substrates to receive Pigmented Epoxy Mortar Resin Product #24 must be properly prepared as outlined in Epoxy Surface Preparation Procedures. Epoxy.com technical service department is pleased to answer any questions.

INSTALLATION

Will vary with application method.

PHYSICAL PROPERTIES

Color Light Grey, Taupe, Sand, Dark Grey, Old Gold, Slate Blue, Mocha, Colonial Green, Brick Red, Deep Blue, White. Black, Safety Yellow
Gloss, 60°F 85-1 00
Weight/gallon 9.00-9.5mixed
Solids Content 100%
Mix Ratio 4A to I B by volume
Pot Life 30-40minutes @ 70°F
Viscosity 950 cps, mixed approx.
VOC 0
10-20 mil film 10-14 hrs.
Light Traffic 16 hrs.
Ultimate Cure @ 74°F 5 days
Dry Time @ 50°F 14 days

Epoxy.com Product #24 Colored Epoxy Mortar Resin Color Chart Click the picture of color card below  for a larger version of this picture of the color chart.
Please note:  The picture to the right is a photographic reproduction of the color card for this product.  The photo reproduction process and your monitor and/or printer will change these colors.  This chart is to give you an idea of the colors available and not intended for critical color selections.

CHEMICAL RESISTANCE

R-Recommended for continuous service. L-Limited recommendation, occasional spills.

REAGENT

RATING

REAGENT

RATING

Acetic Acid-5% L Lactic Acid-15% R
Acetone L Methyl Ethyl Ketone L
Bleach L Nitric Acid-10% R
Citric Acid-30% R Skydrol R
Crude Oil R Sodium Hydroxide-50%   R
Diesel Fuel R Sulfuric Acid-20% R
Ethylene Glycol R Toluene R
Fatty Acids L Urea R
Gasoline R Vinegar L
Hydrochloric Acid-15%   R Xylene R

PERFORMANCE PROPERTIES

Tensile Strength ASTM-D-638 8500 psi
Elongation ASTM-D-638 5.5%
Adhesion to metal 2500 psi
Adhesion to concrete ACI Committee 403 350 psi (concrete fails)
Hardness ASTM-D-2240 80 (Shore D)
Abrasion Resistance ASTM-C-501 35-40 mg loss
(CS-17 wheel, 1 kg load, 1000 cycles)
Service Temperature MIL- D-3134F 160 F (immersion)
185 F (dry heat)
Impact Resistance MIL-D3134F § 4.7.3 Withstands 16ft/lbs.
no cracking, delamination or chipping.
Indentation MIL-D-3134F §4.7.4 Withstands 2,000 lbs./sq. in. for 30 min.
without indentation.
Elevated Temperature Resistance
MIL-D-31 34F §4 7 5
No slip or flow
at required temperatures at 158°F
Water Absorption ASTM-D-670-63 (24. hr. immersion) 0.10% maximum
Flexural Strength ASTM-D-790 8,000 psi
Compressive Strength ASTM-D-695 11,000 psi
 

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems ,
Since 1980 - Over 33 years
Florida & Vermont
USA


Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time) .
Closed 12 Noon-1PM Eastern Time for Lunch

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Fontaine, VP - Customer Service Director
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks
We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.

Copyright © 1994-2015 EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.