Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Epoxy.com Product #630 Conductive

Chemical Resistant Novolac Conductive Flooring

Formerly Called Epoxy.com Product #629


DESCRIPTION

Epoxy.com Product #630 Chemical Resistant Conductive Flooring is a 100% solids epoxy Novolac Conductive coating ideal for severe chemical and solvent storage requiring conductive and spark proof surfaces. Applied at a nominal 1/16 inch, the Conductive Novolac offers the superior chemical resistance of a Novolac Resin System while maintaining a conductive surface.

  • Low viscosity ideal for trowel application
  • Exhibits excellent resistance to strong acids, alkalis and most industrial chemicals and solvents
  • 100% Solids low odor application and cure (0-VOC)
  • Bonds well to cool, damp substrates
  • Conductive & non sparking, 25,000 to 1,000,000 ohms resistivity

CONSIDERATIONS

  • Substrate temperature must be a minimum of 50oF
  • Substrate must be free of dirt, waxes, curing agents and other foreign materials
  • Steel surfaces must e free of grease and oils.  Abrasive blast to SSPC-SP-3

COMPOSITION

100% Solids, modified polyamine, cured epoxy Novolac resin and fillers

APPLICATION

SURFACE PREPARATION

Surface Preparation is the most critical portion of any successful resinous flooring system application. All substrates must be properly prepared as outlined in Epoxy.com Surface Preparation Guide.

INSTALLATION

Installation of Epoxy.com Product #630 NOVOLAC CONDUCTIVE will vary with application. Normally spread with a trowel or squeegee and back-rolled with a medium or short nap roller. Care should be taken to minimize the entrapment of air caused by over rolling.

For complete instructions, consult installation guide or Epoxy.com Technical Support.

CLEAN-UP

Clean skin with soap and water. Tools and equipment should be cleaned with xylene or lacquer thinner.

Product #630 NOVOLAC CONDUCTIVE will yield approximately 32 mils when spread at 50 ft 2 per gallon. Two coats required.

COLOR

Epoxy.com Product #630 CONDUCTIVE is available in Epoxy.com Standard Colors and Custom Colors as approved.

Epoxy.com Epoxy Color Chart HereClick the picture of color card at the side for a larger version of this picture of the color chart.
Please note:  The picture to the right is a photographic reproduction of the color card for this product.  The photo reproduction process and your monitor and/or printer will change these colors.  This chart is to give you an idea of the colors available and not intended for critical color selections.

 

TECHNICAL DATA

Viscosity @ 75oF 1,000-1,500 cps
Mixing Ratio by volume 2 Part A to 1 Part B by Volume
Solids Content by volume 100 by volume
Volatile Organic Content 0
Weight per gallon, mixed 11.0-11.5 lbs. per gallon mixed

CURE/DRY TIME

Pot Life 20-25 min. @75  Degrees F
Dry to Touch 6-7 hours @ 75  Degrees F
Re-Coat 8-12 hours @ 7 5Degrees F
Light Service 24 hours @ 75 Degrees F
Full Cure & Maximum Resistance 5 days

CHEMICAL RESISTANCE

REAGENT RATING
Acetic Acid-10%, 30% R
Acetone L
Ammonia Hydroxide-38 % R
Beer R
Bleach L
Brake Fluid R
Citric Acid-30% R
Citric Acid-40% R
Crude Oil R
Diesel Fuel R
Ethylene Glycol R
Fatty Acids R
Gasoline R
Hydrochloric Acid-37% R
Lactic Acid-50 R
Lactic Acid-80% R
Methyl Ethyl Ketone R
Methylene Chloride L
Nitric Acid-10% R
Peroxide-35% L
Phosphoric Acid R
Skydrol R
Sodium Hydroxide-50% R
Sulfuric Acid-98% R
Toluene R
Urea R
Vinegar R
Xylene R

R-Recommended for continuous service

L-Limited Recommendation, occasional spills

*-May cause slight stain or discoloration

MAINTENANCE

See Epoxy.com Care and Maintenance of Seamless Flooring.

Epoxy.com Product #630 NOVOLAC CONDUCTIVE is easily cleaned with neutral soaps or detergents.

Skip Navigation Links
Epoxy.com Home PageExpand Epoxy.com Home Page

Skip Navigation Links

Proper mixing and installation is critical to the optimal success of all products.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
A Vermont Corporation
USA

We have products that have passed the test of time as well as the best new Systems available today.

Since 1980 - 40 years of the highest quality products

Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time)

Closed for lunch from 12Noon to 1PM


321-206-1833  Customer Service - Ordering and Order Status
                         Katey Lambert-Fontaine, VP - Chief Operations Officer
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO

Copyright © 1994-2023 (providing online information about the right product for the right job for nearly 30 years)  EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks
We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.