Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Epoxy Chip Flooring Base Coating

High-Build Coating100% Solids

Epoxy.com Product #315BC


GENERAL DESCRIPTION

Epoxy.com Product #315BC High-Build Polymeric Coating is a two component, 100% solids polymeric Hi-Build polymeric coating used for high foot and light forklift traffic areas where abrasion resistance is required; for protection against mild corrosion; and as a decorative waterproof coating for walls, floors, tanks, pools etc. Also used as a base coat for Epoxy.com Chip Flooring System.

ADVANTAGES

Epoxy.com Coating on a Water Tank
  • Moisture Insensitive
  • Ceramic like finish
  • Sprayable
  • Solvent Free
  • Waterproof
  • Extremely Durable
  • Chemical Resistant

SURFACE PREPARATION

Surface  to receive Epoxy.com Product #315BC High-Build Polymeric Coating must be clean and sound. Remove all dirt, laitance, grease curing compounds and other foreign matter by sandblasting, or mechanical abrasion. Remove water and dust from all surfaces with an oil free blast immediately prior to application.

MIXING INSTRUCTIONS

Temperature of Epoxy.com Product #315BC High-Build Polymeric Coating (normal cure) must be 50° F or above at time of mixing. Stir each component separately before blending. Mix two parts by volume of Part A with one part by volume of Part  B for three minutes with a low speed electric drill motor equipped with a mixing paddle. 

APPLICATION

ApplyEpoxy.com Product #315BC High-Build Polymeric Coating with a roller, brush, or spray equipment.  When not used as part of the 315 Chip Flooring System, 2 coats are recommended. Thickness per coat should be 7-10 mils. Seven days cure time is required to reach maximum chemical resistance. When installing over concrete Product #899 or Product #203 Primer is recommended.

LIMITATIONS

DO NOT apply Epoxy.com Product #315BC High-Build Polymeric Coating at temperatures below 50° F. Surface must be dry.

SAFETY PRECAUTIONS

Prolonged or repeated exposure may cause eye and skin irritation. If contact occurs, wash immediately and seek medical help. Use safety glasses with side shields and wear protective rubber gloves.

CLEANING

All tools and equipment should be cleaned before the system gels. Use MEK, Acetone, or any lacquer solvent

APPLICATION PROPERTIES @77°F

Mix Ratio  2:1 By Volume 
Viscosity (mixed) 950 CPS       
Pot Life (200 gr.) in minutes @70° F. 30-40(normal cure)
Set Time in Hours @ 70° F. 10-12 (normal cure)
Initial Cure 24 Hours
Final Cure 5 Days
Packaging Unit Size 3 gallon units (2 gallons of "A" + 1 gallon of "B"
Standard Colors White, Light Gray, Dark Gray, Taupe, Sand,
Old Gold, Mocha, Brick Red, Slate Blue,
Colonial Green, Deep Blue, Black, Safety Yellow
Color Chart HereClick the picture of color card below  for a larger version of this picture of the color chart.
Please note:  The picture to the right is a photographic reproduction of the color card for this product.  The photo reproduction process and your monitor and/or printer will change these colors.  This chart is to give you an idea of the colors available and not intended for critical color selections.

Material Certification of LEED Requirements

Epoxy.com a division of Epoxy Systems, Inc. certifies that Epoxy.com  meet or exceed LEED requirements as summarized below:

LEED Credit IE 4.2:

Indoor Environmental Quality/Air Quality Before Occupancy Materials meet the requirement for VOC content Pertaining to LEED IEQ 4.2 Indoor Emitting Materials Credit. Refer to the individual product component technical data sheets and MSDS for further information.

Other customers who visited this page also visited:

Proper mixing and installation is critical to the optimal success of all product.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
20774 W. Pennsylvania Ave.
Dunnellon, Florida 34431
Hundreds of Systems,
Since 1980 - 35 years
Florida & Vermont
USA


Customer and Technical Support Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time).
Closed 12 Noon-1PM Eastern Time for Lunch

321-206-1833  Customer Service - Ordering and Order Status
                         Katey Fontaine, VP - Customer Service Director
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO
                         office@epoxy.com

352-489-1625   Fax line to all Departments

Get important hint, tips, tricks, and product information:  Visit our Blog, and join us on Facebook and Twitter.

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks

Copyright © 1994-2017 - Epoxy Systems Inc. DBA Epoxy.com  - Commercial, Industrial, and Residential Resins Since 1980

/